New Products

Spring washer M5

Spring washer M6 for pressure plate attachment Puch

Spring washer for M10 - Form B galvanized - e.g. for brake eccentric Puch 500/650/700 with Puch brake drum

spring washer

Puch Haflinger splint for castellated nut on steering gear

Steel hammer screw MR 3x6 - bright - e.g. for nameplate

Retaining rings for dust boot

Insulating plate at interrupter cast distributor

Hex nut M4 stainless steel A4 - reed valve and tank sender

Hutmutter

Seat hook narrow

Hex nut M3 stainless steel A2 for Puch wart indicator attachment

Screw for pressure plate attachment M6x16 Puch - for 160mm pressure plate

Spring for reflector on trim ring Fiat and Puch

Out of stock

self locking nut M7 for shaft for the cam followers

Woodruff key for Dynastarter

O-ring tie rod Haflinger

O-ring half-axle bolt last series Haflinger

Gasket speedometer drive

Valve wedge, self-rotating (501.1.05.083.1)

Spacer for wheel reduction Haflinger 42x52x0.3 - alternative instead of spacer ring / pressure ring

Seal for side screw for transmission oil filler Puch 500/650/700/Haflinger

Hexagon nut M6 galvanized - for Puch headlight adjustment screws

O-Ring

Spacer for wheel reduction Haflinger 42x52x0.1 - alternative instead of spacer ring / pressure ring

Nut M8 wrench size 13 - galvanized - for Haflinger bumper

O-ring Front 22/26/2

Grommet for example from Eberspächer heater

Gasket regulator housing

O-ring Front

gasket pump cover (Weber)

Grommet for ignition coil

Out of stock

Grease nipple M6x1

Spacer for wheel reduction Haflinger 42x52x0.2 - alternative instead of spacer ring / pressure ring

Cylinder screw M3x16 stainless steel A2 for indicator Celon attachment with Puch aluminum base

Seat hook wide

Hexagon nut M10 wrench size 17

Nut M7 wrench size 11

Hexagon nut M7, 3mm high

Speedometer wheel thrust washer for Steyr Puch 500/650/700 / Steyr Puch Haflinger and Pinzgauer

Thrust washer / spacer washer for angle lever and rocker arm

rubber sleeve

O-ring Front 38/44/3

jet inspection cover gasket

O-ring steering linkage Haflinger

Hose clamp 9-11mm

M8 nut spanner 14

Rubber grommet 30x19

Toothed washer M5 stainless steel A2 e.g. for countersunk screw buffer plate suicide doors

Gasket housing cover

Cylindrical screw M3x10 stainless steel A2 for wart turn signal attachment

O-ring front axle Haflinger

M8 nut wrench size 12

Plug for Steyr Puch two-cylinder engine block

Verschlusspropfen

Reinforced washer

gasket for choke

O-Ring (900.3785)

M8 nut wrench size 10

Dowel for bearing bushing holder - large crankshaft

Key 15 mm (501.1.0206)

Rubber grommet 28x16 e.g. choke cable Haflinger

Nut M8 wrench size 13 - stainless steel A2 - for Haflinger bumper

Hose clamp for oil breather

idle mixture screw spring/feather

Sealing plug / stop rubber Haflinger seat cover

Ball for ball socket Haflinger

sealing to starter body

Puch shim 1mm at belt pulley for V-belt tension

Seal for preheating pipe (501.1.0827)

Bulb 12V 4W for parking light and side indicator (901.0778)

Puch shim 0.5mm for belt pulley for V-belt tension

Locking plate 2.5mm for mounting bracket for slide plate, right

Cable grommet bumper Haflinger / choke cable Puch 500 (501.1.2741)

sandwich plate for carburetor (Zenith)

Bulb 12V 2W Ø 6.8mm

sandwich plate (0,5)

Rubber bushing for struts (700.1.41.203.1)

gasket between carburetor housing/throttle body

Stud M10x40mm - connection between Puch engine and gearbox

Key 17mm (501.1.0209)

Puch license plate light festoon lamp 12V 3W - 8x28

Screw M12x45 for Puch engine mount

Carburetor cover gasket

screw cover for carburetor (Zenith)

rubber band under tachometer

Underlay rubber oil pressure and oil temperature 60 mm

Rubber plug floor pan without exhaust heating Haflinger

sealing to the lower oh lacing pin

Underlay rubber tachometer 80mm

Steyr Puch cleaning cloth

Plastic sleeve for windscreen wipers

Spring for bypass valve at Puch oil filter housing - soft

Fuel Filter f. 6 and 8 mm hose diameter

Gasket under turn signal with aluminum base for front mask / front panel 1959 - 1968

Hexagon nut M14x1.5 stainless steel A2 - for steering gear Puch and Fiat

carburetor cover gasket

Rubber grommet 10x1.5 mm e.g. for Puch standlich in the headlight

Sealing flange 40 PID Solex